The SpiderSoM is a programmable, non-volatile solution based on Intel® MAX®10 FPGA, which enables it to deliver full-featured FPGA capabilities.
The SpiderSoM can be used with the standard baseboard (SpiderBase) as a complete building block or can be plugged into existing designs and products as functional part. It connects to its baseboard via a 230pins MXM2 connector and provides the ideal solution support for various soft-core CPUs, video-processing algorithms, etc.
The SpiderSoM is available as a low cost and extremely flexible platform which enables user to setup a running system according to the required specification in a very short time. SoM is based on the free and open design concept: KiCAD design files are available under CERN OHL v1.2.
USB Firmware for MX10 and SpiderSoM
MX10 and SpiderSoM modules provide a USB device interface implemented with PIC16F1454 microcontroller (MCU). On the SoM side the MCU is connected to three interfaces: serial (if the other side is implemented inside the FPGA), I2C bus (connected to the module PMIC, charge controller, RTC and FPGA), and FPGA JTAG programming interface.
On the host side Linux is supported as Operating System, currently Ubuntu16.04LTS is marked as a reference base.
MAX 10 single voltage supply FPGA in U169 package
module supports MAX 10 FPGAs from 10M02SC to 10M16SA
optional 4 MiB SPI NOR
optional 4 GiB e.MMC
optional 8 MiB SDRAM
FPGA GPIO pins
optional RTC with battery backup
optional Li-Ion/Li-Pol charger
Size: 70mm x 35mm
OS Support:
FreeRTOSTM
The SpiderSoM promotes the free and open design concept: KiCAD design files are available under CERN OHL v1.2.
While the MX10 SoM targets the area of professional electronic designs in commercial applications the SpiderSoM was designed to be used in IoT Maker applications.
Features:
Four momentary pushbuttons;
Debouncing filters;
Inverting Schmitt Triggers;
Small PCB size for flexible designs 3.0 cm × 2.0 cm;
6-pin Pmod connector with GPIO interface.
Pmod BTN gives users four momentary pushbuttons for easy user inputs to a system board.
Custom antistatic Pmod packaging is included.
Features:
Rotary push-button shaft encoder;
Add multiple types of user input to host board or project;
Additional static slide switch;
Small PCB size for flexible designs 3.8 cm × 2.0 cm;
6-pin Pmod connector with GPIO interface.
Pmod ENC features a rotary shaft encoder with an integral push-button to provide multiple types of outputs such as a way for users to quickly switch between multiple choices shown on a screen or predefined motor speeds. The module also includes a sliding switch that is commonly used as an on/off output. An encoder is commonly used in freely rotating volume knobs to detect how many "clicks" a knob has been rotated.
Custom antistatic Pmod packaging is included.
Features:
Maxim Integrated MAX3232 RS232 transceiver;
Standard RS232 DB9 connector;
Optional RTS and CTS handshaking functions;
Small PCB size for flexible designs 2.5 cm × 3.3 cm;
6-pin Pmod connector with UART interface.
Pmod RS232 converts between digital logic voltage levels to RS232 voltage levels using the Maxim Integrated MAX3232 transceiver. The RS232 module is configured as a data communications equipment (DCE) device. It connects to data terminal equipment (DTE) devices, such as the serial port on a PC, using a straight-through cable.
Custom antistatic Pmod packaging is included.
Features:
Ultra-sensitive GPS module (-165 dBm);
Add 3m 2D satellite positioning accuracy to any embedded system;
Low power consumption;
Up to 10Hz update rate;
NMEA (default) and RTCM protocols available;
Small PCB size for flexible designs 5.0 cm × 2.0 cm;
6-pin Pmod connector with UART interface.
Pmod GPS can provide satellite positioning accuracy to any embedded system. By communicating through UART with the GlobalTop FGPMMOPA6H GPS module, users may benefit from the 3 meter accuracy for any long term traveling.
Custom antistatic Pmod packaging is included.
Features:
Eight high-brightness green LEDs;
Uses BJTs for low-power logic level control;
Small PCB size for flexible designs 2.8 cm × 2.0 cm;
2×6-pin Pmod connector with GPIO interface.
Pmod 8LD has eight high-brightness LEDs that are driven by logic level transistors so that each LED can be individually illuminated from a logic high signal.
Custom antistatic Pmod packaging is included.
Features:
4 slide switches;
Add user input to host board or project;
Static binary logic input;
Small PCB size for flexible designs 3.3 cm × 2.0 cm;
6-pin Pmod connector with GPIO interface.
Pmod SWT provides users with four slides switches for up to 16 different binary logic inputs to for the attached system board.
Custom antistatic Pmod packaging is included.
Features:
USB to serial UART interface;
Micro USB connector;
Option to power the system board through the FTDI chip;
Small PCB size for flexible designs 2.5 cm × 2.0 cm;
6-pin Pmod connector with UART interface.
Pmod USBUART provides a USB to UART cross-conversion through the FTDI FT232R. Users may send data in either direction on the Pmod and receive the converted data in the appropriate format.
Custom antistatic Pmod packaging is included.
Features:
High-speed RS-485 communication module;
Isolated RS-485/RS-422 interfaces for use in noisy environments;
16Mbps maximum data rate;
Connect up to 256 nodes on one bus;
Differential half or full-duplex communication;
Thermal shutdown and ±15kV ESD protection;
6-pin Pmod connector with UART interface.
Pmod RS485 is a high-speed communication module powered by the Analog Devices ADM582E. By communicating with the device via UART, users can take advantage of the RS485 communication protocol with speeds up to 16 Mbps.
Custom antistatic Pmod packaging is included.
Features:
Real-time clock/calendar with lithium coin cell back-up;
Multi-function pin output that can generate a square wave;
Two available alarms;
128 bytes EEPROM;
64 bytes SRAM;
Small PCB size for flexible designs 3.3 cm × 2.0 cm;
2×4-pin connector with I2C interface.
Pmod RTCC is a real-time clock/calendar powered by the Microchip MCP79410. Through the I2C interface, users may configure up to two alarms that can be triggered at a wide variety of possible times.
Custom antistatic Pmod packaging is included.
The SpiderSoM-S provides
10M08SA MAX10 FPGA
1 ADC
25MHz clock
4MiB SPI NOR
130 GPIOs, 3,3V I/O voltage
The SpiderSoM is a programmable, non-volatile solution based on Intel® MAX®10 FPGA, which enables it to deliver full-featured FPGA capabilities.
The SpiderSoM can be used with the standard baseboard (SpiderBase) as a complete building block or can be plugged into existing designs and products as functional part. It connects to its baseboard via a 230pins MXM2 connector and provides the ideal solution support for various soft-core CPUs, video-processing algorithms, etc.
The SpiderSoM is available as a low cost and extremely flexible platform which enables user to setup a running system according to the required specification in a very short time. SoM is based on the free and open design concept: KiCAD design files are available under CERN OHL v1.2.
USB Firmware for MX10 and SpiderSoM
MX10 and SpiderSoM modules provide a USB device interface implemented with PIC16F1454 microcontroller (MCU). On the SoM side the MCU is connected to three interfaces: serial (if the other side is implemented inside the FPGA), I2C bus (connected to the module PMIC, charge controller, RTC and FPGA), and FPGA JTAG programming interface.
On the host side Linux is supported as Operating System, currently Ubuntu16.04LTS is marked as a reference base.
MAX 10 single voltage supply FPGA in U169 package
module supports MAX 10 FPGAs from 10M02SC to 10M16SA
optional 4 MiB SPI NOR
optional 4 GiB e.MMC
optional 8 MiB SDRAM
FPGA GPIO pins
optional RTC with battery backup
optional Li-Ion/Li-Pol charger
Size: 70mm x 35mm
OS Support:
FreeRTOSTM
The SpiderSoM promotes the free and open design concept: KiCAD design files are available under CERN OHL v1.2.
While the MX10 SoM targets the area of professional electronic designs in commercial applications the SpiderSoM was designed to be used in IoT Maker applications.
Spider SoM configurations:
SpiderSoM-L
SpiderSoM-S
FPGA
10M02SC MAX10
10M08SA MAX10
ADC
-
1
Clock
25 MHz XO
25 MHz XO
DDR3 RAM
-
-
SPI NOR
-
4MiB
e.MMC NAND Flash
-
-
RTC
-
-
GPIO/ LVDS TX/Rx
130/ 13/ 16
130/ 13/ 16
Li-Ion charger
-
-
I/O Voltage
programmable 3.3V
Temperature range
0oC ... +70oC
0oC ... +70oC
Size
70mm x 35mm
70mm x 35mm
€41.00*
This website uses cookies to ensure the best experience possible. More information...
