SpiderBase

€31.00*

Prices excl. VAT plus shipping costs

System on Module

MX10-L

MX10-S8

MX10-S16

MX10-U

SpiderSoM-L

SpiderSoM-S

Product number: SpiderBase

Product information "SpiderBase"

The Spiderboard Baseboard is a unique baseboard, designed to host the Spiderboard SoM / MX10 SoM based on Intel PSG (former Altera®) MAX® 10 FPGAs.

Features:

simple baseboard in 2 layer design
compatibility to the Spiderboard SoM as well as the MX10 SoM.
open hardware
MxM2 pcb edge connector
every pin of the MxM2 connector module is accessible at one of the pinheaders
large 25x15 .1” prototyping area
4 PMOD compatible headers (3.3V or 5V supply voltage selectable)
2 user push buttons
reset and power buttons
2 user LEDs
Arduino shield compatible interface
Intel PSG Blaster compatible programming interfaces
USB mini B connector
CR2032 cell holder
JST-2.0 lithium battery connector
configuration jumpers (e.g. boot selection for MX10 module)

MX10 SoM / SpiderSoM configurations:

	MX10-L	MX10-S8	MX10-S16	MX10-U	SoM-L	SoM-S
FPGA	10M04DC F256	10M08DA F256	10M16DA F256	10M50DA F256	10M02SC MAX10	10M08SA MAX10
ADC	-	1	1	2	-	1
Clock	25 MHz XO	25 MHz XO	25 MHz XO, PLL IDT5P49V5923	25 MHz XO, PLL IDT5P49V5923	25 MHz XO	25 MHz XO
DDR3 RAM	-	-	128 MB	512 MB	-	-
SPI NOR	-	-	-	4 MB	-	4MiB
e.MMC NAND Flash	-	-	4 GB	4 GB	-	-
RTC	-	-	-	MPC794xx	-	-
GPIO/ LVDS TX/Rx	100/ 13/ 16	100/ 13/ 16	100/ 13/ 16	100/ 13/ 16	130/ 13/ 16	130/ 13/ 16
Li-Ion charger	LTC 4155	-	-	LTC 4155	-	-
I/O Voltage	programmable 1.8V/ 2.5V/ 3.0V/ 3.3V				3.3V	3.3V
Temperature range	0^oC ... +70^oC	0^oC ... +70^oC	0^oC ... +70^oC	0^oC ... +70^oC	0^oC ... +70^oC	0^oC ... +70^oC
Size	70mm x 35mm	70mm x 35mm	70mm x 35mm	70mm x 35mm	70mm x 35mm	70mm x 35mm

Accessory Items

Pmod 8LD

Features: Eight high-brightness green LEDs; Uses BJTs for low-power logic level control; Small PCB size for flexible designs 2.8 cm × 2.0 cm; 2×6-pin Pmod connector with GPIO interface. Pmod 8LD has eight high-brightness LEDs that are driven by logic level transistors so that each LED can be individually illuminated from a logic high signal. Custom antistatic Pmod packaging is included.

€8.70*

Pmod SWT

Features: 4 slide switches; Add user input to host board or project; Static binary logic input; Small PCB size for flexible designs 3.3 cm × 2.0 cm; 6-pin Pmod connector with GPIO interface. Pmod SWT provides users with four slides switches for up to 16 different binary logic inputs to for the attached system board. Custom antistatic Pmod packaging is included.

€6.00*

Pmod USBUART

Features: USB to serial UART interface; Micro USB connector; Option to power the system board through the FTDI chip; Small PCB size for flexible designs 2.5 cm × 2.0 cm; 6-pin Pmod connector with UART interface. Pmod USBUART provides a USB to UART cross-conversion through the FTDI FT232R. Users may send data in either direction on the Pmod and receive the converted data in the appropriate format. Custom antistatic Pmod packaging is included.

€18.00*

Pmod RS485

Features: High-speed RS-485 communication module; Isolated RS-485/RS-422 interfaces for use in noisy environments; 16Mbps maximum data rate; Connect up to 256 nodes on one bus; Differential half or full-duplex communication; Thermal shutdown and ±15kV ESD protection; 6-pin Pmod connector with UART interface. Pmod RS485 is a high-speed communication module powered by the Analog Devices ADM582E. By communicating with the device via UART, users can take advantage of the RS485 communication protocol with speeds up to 16 Mbps. Custom antistatic Pmod packaging is included.

€40.00*

Pmod RTCC

Features: Real-time clock/calendar with lithium coin cell back-up; Multi-function pin output that can generate a square wave; Two available alarms; 128 bytes EEPROM; 64 bytes SRAM; Small PCB size for flexible designs 3.3 cm × 2.0 cm; 2×4-pin connector with I2C interface. Pmod RTCC is a real-time clock/calendar powered by the Microchip MCP79410. Through the I2C interface, users may configure up to two alarms that can be triggered at a wide variety of possible times. Custom antistatic Pmod packaging is included.

€16.00*

Pmod BTN

Features: Four momentary pushbuttons; Debouncing filters; Inverting Schmitt Triggers; Small PCB size for flexible designs 3.0 cm × 2.0 cm; 6-pin Pmod connector with GPIO interface. Pmod BTN gives users four momentary pushbuttons for easy user inputs to a system board. Custom antistatic Pmod packaging is included.

€7.00*

Pmod ENC

Features: Rotary push-button shaft encoder; Add multiple types of user input to host board or project; Additional static slide switch; Small PCB size for flexible designs 3.8 cm × 2.0 cm; 6-pin Pmod connector with GPIO interface. Pmod ENC features a rotary shaft encoder with an integral push-button to provide multiple types of outputs such as a way for users to quickly switch between multiple choices shown on a screen or predefined motor speeds. The module also includes a sliding switch that is commonly used as an on/off output. An encoder is commonly used in freely rotating volume knobs to detect how many "clicks" a knob has been rotated. Custom antistatic Pmod packaging is included.

€8.00*

Pmod RS232

Features: Maxim Integrated MAX3232 RS232 transceiver; Standard RS232 DB9 connector; Optional RTS and CTS handshaking functions; Small PCB size for flexible designs 2.5 cm × 3.3 cm; 6-pin Pmod connector with UART interface. Pmod RS232 converts between digital logic voltage levels to RS232 voltage levels using the Maxim Integrated MAX3232 transceiver. The RS232 module is configured as a data communications equipment (DCE) device. It connects to data terminal equipment (DTE) devices, such as the serial port on a PC, using a straight-through cable. Custom antistatic Pmod packaging is included.

€13.10*

Pmod GPS

Features: Ultra-sensitive GPS module (-165 dBm); Add 3m 2D satellite positioning accuracy to any embedded system; Low power consumption; Up to 10Hz update rate; NMEA (default) and RTCM protocols available; Small PCB size for flexible designs 5.0 cm × 2.0 cm; 6-pin Pmod connector with UART interface. Pmod GPS can provide satellite positioning accuracy to any embedded system. By communicating through UART with the GlobalTop FGPMMOPA6H GPS module, users may benefit from the 3 meter accuracy for any long term traveling. Custom antistatic Pmod packaging is included.

€34.80*

Similar Items

MX10-L

MAX 10 FPGA in F256 package module supports: 10M04DC programmable clock generator (25MHz XO) 100 FPGA GPIO pins, including 13 LVDS transmitters and 16 receivers programmable high-efficient PMIC, FPGA IO voltages are configurable Li-Ion charger (LTC4155) Temperature range: 0oC...+70oC Size: 70mm x 35mm

€57.00*

MX10-S16

MAX 10 FPGA in F256 package module supports: 10M16DA 1 x ADC 4 GB e.MMC 128 MB DDR3 DRAM programmable clock generator (25MHz XO) and PLL (IDT5P49V5923) 100 FPGA GPIO pins, including 13 LVDS transmitters and 16 receivers programmable high-efficient PMIC, FPGA IO voltages are configurable Temperature range: 0oC...+70oC Size: 70mm x 35mm

€100.00*

SpiderSoM-S

System on Module: SpiderSoM-L

The SpiderSoM-S provides 10M08SA MAX10 FPGA 1 ADC 25MHz clock 4MiB SPI NOR 130 GPIOs, 3,3V I/O voltage The SpiderSoM is a programmable, non-volatile solution based on Intel® MAX®10 FPGA, which enables it to deliver full-featured FPGA capabilities. The SpiderSoM can be used with the standard baseboard (SpiderBase) as a complete building block or can be plugged into existing designs and products as functional part. It connects to its baseboard via a 230pins MXM2 connector and provides the ideal solution support for various soft-core CPUs, video-processing algorithms, etc. The SpiderSoM is available as a low cost and extremely flexible platform which enables user to setup a running system according to the required specification in a very short time. SoM is based on the free and open design concept: KiCAD design files are available under CERN OHL v1.2. USB Firmware for MX10 and SpiderSoM MX10 and SpiderSoM modules provide a USB device interface implemented with PIC16F1454 microcontroller (MCU). On the SoM side the MCU is connected to three interfaces: serial (if the other side is implemented inside the FPGA), I2C bus (connected to the module PMIC, charge controller, RTC and FPGA), and FPGA JTAG programming interface. On the host side Linux is supported as Operating System, currently Ubuntu16.04LTS is marked as a reference base. MAX 10 single voltage supply FPGA in U169 package module supports MAX 10 FPGAs from 10M02SC to 10M16SA optional 4 MiB SPI NOR optional 4 GiB e.MMC optional 8 MiB SDRAM FPGA GPIO pins optional RTC with battery backup optional Li-Ion/Li-Pol charger Size: 70mm x 35mm OS Support: FreeRTOSTM The SpiderSoM promotes the free and open design concept: KiCAD design files are available under CERN OHL v1.2. While the MX10 SoM targets the area of professional electronic designs in commercial applications the SpiderSoM was designed to be used in IoT Maker applications. Spider SoM configurations: SpiderSoM-L SpiderSoM-S FPGA 10M02SC MAX10 10M08SA MAX10 ADC - 1 Clock 25 MHz XO 25 MHz XO DDR3 RAM - - SPI NOR - 4MiB e.MMC NAND Flash - - RTC - - GPIO/ LVDS TX/Rx 130/ 13/ 16 130/ 13/ 16 Li-Ion charger - - I/O Voltage programmable 3.3V Temperature range 0oC ... +70oC 0oC ... +70oC Size 70mm x 35mm 70mm x 35mm

€41.00*

MX10-S8

MAX 10 FPGA in F256 package module supports: 10M08DA 1 x ADC programmable clock generator (25MHz XO) 100 FPGA GPIO pins, including 13 LVDS transmitters and 16 receivers programmable high-efficient PMIC, FPGA IO voltages are configurable Temperature range: 0oC...+70oC Size: 70mm x 35mm

€66.00*

MX10-U

MAX 10 FPGA in F256 package module supports: 10M50DA 2 x ADC 4 MB SPI NOR 4 GB e.MMC 128 MB DDR3 DRAM programmable clock generator (25MHz XO) and PLL (IDT5P49V5923) 100 FPGA GPIO pins, including 13 LVDS transmitters and 16 receivers RTC (MPC794xx) with battery backup programmable high-efficient PMIC, FPGA IO voltages are configurable Li-Ion charger (LTC4155) Temperature range: 0oC...+70oC Size: 70mm x 35mm

€183.00*

SpiderSoM-L

The SpiderSoM-L provides 10M02SC MAX10 FPGA 25MHz clock 130 GPIOs, 3,3V I/O voltage The SpiderSoM is a programmable, non-volatile solution based on Intel® MAX®10 FPGA, which enables it to deliver full-featured FPGA capabilities. The SpiderSoM can be used with the standard baseboard (SpiderBase) as a complete building block or can be plugged into existing designs and products as functional part. It connects to its baseboard via a 230pins MXM2 connector and provides the ideal solution support for various soft-core CPUs, video-processing algorithms, etc. The SpiderSoM is available as a low cost and extremely flexible platform which enables user to setup a running system according to the required specification in a very short time. SoM is based on the free and open design concept: KiCAD design files are available under CERN OHL v1.2. USB Firmware for MX10 and SpiderSoM MX10 and SpiderSoM modules provide a USB device interface implemented with PIC16F1454 microcontroller (MCU). On the SoM side the MCU is connected to three interfaces: serial (if the other side is implemented inside the FPGA), I2C bus (connected to the module PMIC, charge controller, RTC and FPGA), and FPGA JTAG programming interface. On the host side Linux is supported as Operating System, currently Ubuntu16.04LTS is marked as a reference base. MAX 10 single voltage supply FPGA in U169 package module supports MAX 10 FPGAs from 10M02SC to 10M16SA optional 4 MiB SPI NOR optional 4 GiB e.MMC optional 8 MiB SDRAM FPGA GPIO pins optional RTC with battery backup optional Li-Ion/Li-Pol charger Size: 70mm x 35mm OS Support: FreeRTOSTM The SpiderSoM promotes the free and open design concept: KiCAD design files are available under CERN OHL v1.2. While the MX10 SoM targets the area of professional electronic designs in commercial applications the SpiderSoM was designed to be used in IoT Maker applications. Spider SoM configurations: SpiderSoM-L SpiderSoM-S FPGA 10M02SC MAX10 10M08SA MAX10 ADC - 1 Clock 25 MHz XO 25 MHz XO DDR3 RAM - - SPI NOR - 4MiB e.MMC NAND Flash - - RTC - - GPIO/ LVDS TX/Rx 130/ 13/ 16 130/ 13/ 16 Li-Ion charger - - I/O Voltage programmable 3.3V Temperature range 0oC ... +70oC 0oC ... +70oC Size 70mm x 35mm 70mm x 35mm

€29.00*